Roll over image to zoom in
INSULATION PLATE DEVICELL DRY 2M2 T
Product code
8109401
Installation and insulation board for renovation and new construction
DEVIcell™ installation and insulation board is suitable for dry areas directly under laminate or wooden flooring. DEVIcell™ enables quick and easy installation of floor heating directly under parquet, laminate, or wooden finishes.
The DEVIcell™ board measures 50 cm x 100 cm and is only 13 mm thick. The DEVIcell™ board consists of a 12 mm thick lower layer of thermal-insulating EPS insulation and an upper layer of approximately 1 mm thick reflective aluminum foil. Thanks to its structure, heat is evenly distributed across the floor, maintaining a comfortable room temperature. Heat is not wasted because the insulation effectively prevents heat loss downward, while the aluminum reflects heat upward. This allows the temperature to reach the desired level quickly.
The boards are compatible with DEVIflex™ 6T (6 W/m) and 10T (10 W/m) heating cables. Ten meters of heating cable are required per square meter of board. This results in a floor power output of 60 W/m² to 100 W/m², achieving ideal heating performance for parquet and laminate floors. When selecting cables, consider the change in cable requirement due to board modifications.
DEVIcell™ board packaging sizes are 2 m², 5 m², and 50 m².
Concrete or panel floors - finish: parquet or laminate.
DEVIcell™ installation and insulation boards are installed on top of existing floors, and the boards are connected to each other using the provided plastic clips. Next, the heating cables are pressed into the grooves of the board, a base material recommended by the parquet or laminate manufacturer is applied on top, and finally the parquet or laminate is installed in place.
Joist floors - finish: wooden planks
Non-compressible thermal insulation is installed between joists spaced at 600 mm. DEVIcell™ installation and insulation boards are installed directly on top of the insulation between the joists, and the boards are connected to each other using the provided plastic clips. The heating cables are pressed into the grooves of the board, and if necessary, the cable is covered with aluminum tape. Finally, the wooden planks are fixed to the floor joists or supports. The best efficiency is achieved when there is no air gap between the DEVIcell™ insulation board and the floor plank, ensuring direct contact.
Not suitable for installation under poured or tiled floors.
Technical specifications:
Structure: Aluminum-coated polystyrene
U-value: 3 W/m²K
Board dimensions: 50 x 100 cm (0.5 m²)
Cable consumption: 10 m / m²
Thickness: 13 mm
Aluminum thickness: 0.8 mm
Insulation: 12 mm fire-retardant EPS
Compressive strength: 3670 kg / m²
Maximum ambient temperature: 80 °C This product description is an automated translation of the original Finnish description.
DEVIcell™ installation and insulation board is suitable for dry areas directly under laminate or wooden flooring. DEVIcell™ enables quick and easy installation of floor heating directly under parquet, laminate, or wooden finishes.
The DEVIcell™ board measures 50 cm x 100 cm and is only 13 mm thick. The DEVIcell™ board consists of a 12 mm thick lower layer of thermal-insulating EPS insulation and an upper layer of approximately 1 mm thick reflective aluminum foil. Thanks to its structure, heat is evenly distributed across the floor, maintaining a comfortable room temperature. Heat is not wasted because the insulation effectively prevents heat loss downward, while the aluminum reflects heat upward. This allows the temperature to reach the desired level quickly.
The boards are compatible with DEVIflex™ 6T (6 W/m) and 10T (10 W/m) heating cables. Ten meters of heating cable are required per square meter of board. This results in a floor power output of 60 W/m² to 100 W/m², achieving ideal heating performance for parquet and laminate floors. When selecting cables, consider the change in cable requirement due to board modifications.
DEVIcell™ board packaging sizes are 2 m², 5 m², and 50 m².
Concrete or panel floors - finish: parquet or laminate.
DEVIcell™ installation and insulation boards are installed on top of existing floors, and the boards are connected to each other using the provided plastic clips. Next, the heating cables are pressed into the grooves of the board, a base material recommended by the parquet or laminate manufacturer is applied on top, and finally the parquet or laminate is installed in place.
Joist floors - finish: wooden planks
Non-compressible thermal insulation is installed between joists spaced at 600 mm. DEVIcell™ installation and insulation boards are installed directly on top of the insulation between the joists, and the boards are connected to each other using the provided plastic clips. The heating cables are pressed into the grooves of the board, and if necessary, the cable is covered with aluminum tape. Finally, the wooden planks are fixed to the floor joists or supports. The best efficiency is achieved when there is no air gap between the DEVIcell™ insulation board and the floor plank, ensuring direct contact.
Not suitable for installation under poured or tiled floors.
Technical specifications:
Structure: Aluminum-coated polystyrene
U-value: 3 W/m²K
Board dimensions: 50 x 100 cm (0.5 m²)
Cable consumption: 10 m / m²
Thickness: 13 mm
Aluminum thickness: 0.8 mm
Insulation: 12 mm fire-retardant EPS
Compressive strength: 3670 kg / m²
Maximum ambient temperature: 80 °C This product description is an automated translation of the original Finnish description.
Product details
Technical specifications
No technical specifications available
Product codes
SAPANU105
STK8109401
PLC8109401
GTIN/EAN5703466228081
Manufacturer part number140F1131
Vendor material number8109401
Basic information
Package measurements (L x W x H)1070 x 510 x 70 mm
Package volume38.199 l
Package weight4.7 kg
Base uniteach
Package units1 / 6 / 10
Package contents–
UNSPSC40101852
BrandDEVI
VendorDANFOSS OY AB
Documents (5)
Brochures & documents
Links